Category: DIY

The Advantages In Using Electric Fence As Your First Line Of Defense

The Advantages In Using Electric Fence As Your First Line Of Defense

When it comes to your personal protection and the protection of your property, is there such a thing as “too much”? Hard to say really. But if you have the time and the means, you should spear no expense in securing your home. Sure, having you very own machine gun turrets installed on the lawn would be excessive indeed, not to mention extremely illegal.

But luckily there are other ways in securing a perimeter, and they’re far less expensive than advanced military technology. Building a fence around the area you’re trying to protect is the way to go; and nothing would be more efficient than your very own electric fence system. Electric fences are less obvious than barbed wire and more efficient, as they can deliver quite a punch to anything and anybody that dare to intrude on your property. To be more precise, the system uses alternative current (A.C.), and via a transformer,turns it into electric pulses. A mechanical trigger is activated when something comes in contact with the wires and the current is released immediately. The current shoots out the power terminal, goes through the wires as high voltage electric pulse (can go as high as 10.000 V) and it’s picked up by a second terminal, which consists of a rod (mostly copper) that’s implanted in the ground. Such fences are highly used today in agriculture (they deliver mild, discomforting shocks to keep animals away) or in prisons (where voltages are lethal).

Such technology is available for everybody who takes prepping and personal safety to the next level. And believe it or not, installing an electric fence has its own advantages over more traditional methods. If done right, you won’t be sorry won’t went for an electric fence instead of barbed wire or anything else. And here’s a list of reasons as to why.

  1. Electric fences are cheaper than traditional fences

Believe it or not, it’s true. The materials are cheaper to buy and the installation process will be cheaper as well. This is because an electric fence requires a lesser quantity of wires and fewer posts as opposed to traditional fencing methods. It’s not meant to be strong and withstand mechanical forces, but rather cover a big enough area to stop all sorts of intrusions. It may be frailer than barbed wire, but it will do some much more than scratch the surface of your skin; it can make you wish you’d never been born.

  1. Electric fences are easier to install

Because the key components are fewer and lighter, you can install your electric fence by yourself, although I’d advice against it. But even if you plan on doing it yourself, make sure you know what you’re doing. The materials aren’t that heavy, not even the posts, so the installation will go faster than if you’d be installing a traditional fence, where you’d need to dig holes. The thin electric fence poles require no such effort from your part; just take them out and stick them in the ground.

  1. Electric fence systems are easily maintained and modified

The system will require very little attention from your part. Just pay some attention to the battery system and the console from time to time, to make sure that everything is working properly. Also, they should be kept clean and dry at all times to avoid unwanted electric discharges and system shutdown. The wires require no maintenance, unless the fence has been hit or damaged in one way or another. Because it has fewer and lighter elements compared to a regular fence, you can modify the structure with ease. You can add or take out poles in a matter minutes.

  1. Electric fences are more efficient overall

The intensity of the electric discharge is customizable, depending of the types of charge you’re using, but also on the materials that the fence is made up of. Barbed wire can be easily cut and taken down by perpetrators, and once the fence is gone, the way is clear. Electric fences can’t be cut, as they’ll release thousands of Vs when the cutting tool comes in contact with the wire. So not only is it hard to go around, but it’s also very hard to interact with a fully charged electric system without getting the shock of a lifetime.

Of course there are some things to keep in mind and consider before installing you very own electric fence. The systems are effective, but you’ll need to keep the area around the fence as clean as possible at all times, so that nothing’s growing in the vicinity of the wires. Growing plants could complicate the situation, so make sure there are none close to the wires.

Thunderstorms could also spell trouble, as the electric discharges could shut the fence down. But repairing the electric fence shouldn’t be much harder then installing it, so that’s a plus. To make it even more effective, you could conceal it, so whoever is trying to breach your “fortress” will get a nasty surprise. However, most states have very specific laws regarding electric fencing visibility and signaling. So do some research and stay out of trouble.

4 Unconventional Uses For Mustard

4 Unconventional Uses For Mustard

Mustard is a great addition to anybody’s kitchen. Not only is it a potent ingredient that will better the taste of pretty much anything it touches (almost anything), but it’s also very healthy. It’s very rich in selenium, nutrients and antioxidants, making it reputable for combating inflammations and relaxing muscles. A single teaspoon of yellow mustard seeds packs about 85mg of omega 3 fats (the good type of fat), 25mg of potassium (K), 29mg of phosphorus (P), 18mg of calcium (Ca) and about 10mg of magnesium (Mg). With so many beneficial elements, no wonder people have been consuming it since antiquity. To Romans were the first to add the mustard seed to their diet, by mixing the ground mustard seeds with wine; the overall result was a condiment which was vastly used in Roman cuisine. The Egyptians saw it also a symbol of good fortune, so they tossed mustard seeds in the tombs of the pharaohs, so they’d have good luck in their next life. The medicinal benefits however, were fully understood later on, in medieval times. The French monks used a mustard-based paste, which was used in treating many ailments: it was used for back pain and muscular relief, for toothaches, as digestive stimulant, for improving blood circulation and clearing up the sinuses. As you can see, it’s an all-purpose tool, and next, I’m going to explain further uses for mustard.

1. Smell Remover

The potent and active enzymes found in mustard will take out any unwanted odor from almost anything. Whether it’s sweat, food smells or even the smell of some disappointing perfume or fabric softener, worry not! Just make a mixture out of 3 gallons of hot water and 1 – 2 cups of dried mustard. Mix it well and add some to a spray bottle. You can spray you car tires, the rims, the underbody of the car, the trunk and the car mats. After the bad smell is gone, you can spray with water and clean with a piece of dry cloth. You could also try spraying the solutions on smelly pieces of clothing, but mustard spots are ussualy very tricky to remove.

2. Natural weedwacker

If you have your very own garden and you’re reluctant to using chemical agents in dealing with your weed problem, you’ll be glad to know that mustard is the eco-friendly way of getting the job done. If you want to, you can event plant mustard every here and there, but I’s even easier to scatter mustard seeds all around the garden. When the mustard seeds come in direct contact with the soil, they’ll discharge some specific nutrients. These nutrients make the soil hostile territory for all sorts of weeds; you’ll reduce your weed problem dramatically. However, mustard can be detrimental to some plants that you might not want gone from your garden, so do some reading on the subject a bit.

3. Burn relief

Mustard works really well on relieving the pain caused by burning accidents, no matter how deep the burn. The first thing you’ll need to do is to get your burned area under cold, running, water. This will alleviate some of the initial stinging sensation and will also clean the burned area. After 20 – 30 seconds, stop the “water treatment” and grab a hold on the jar of mustard. Any type of mustard will do, just spread some all over the burned area and wait a few seconds. The pain should cease in a matter of seconds. Keep in mind though that this is a temporary pain relief solution, not a treatment; you should get yourself checked by a doctor a.s.a.p. to avoid complications.

4. Emergency dishwashing soap

If you’ve run out of dishwashing soap or liquid and you still have tons of dishes to do, once again you can turn to mustard. No need in making that extra trip to the market;

if you have some mustard powder (paste works too) and some baking soda, you’re fine. Just add the two together (2 parts mustard, 1 part baking soda) and mix them up. Apply the resulting mix on the dishes (which have been previously washed with water) and let it sit for 5 – 7 minutes. Once the time is up, simply rinse them with water. You’ll be amazed at how sparkly they’ll be!

I am sure that you’ve understood by now the importance of having some mustard around the house, be it paste, powder or seeds. Mustard van do so much more than making your hotdogs tastier, it will get you out of all sorts of predicaments.

DIY Fertilizers: The Cheap & Easy Way

DIY Fertilizers - The Cheap & Easy Way

As I’ve touched on the subject of survival gardening many times before and I’ve advocated growing your own, private vegetable or even fruit garden, I’m sure that my suggestions have resonated with many of my readers. And if you share my view that your private garden will be your main source of getting fresh produce once the big markets close down, you’ll like what you’ll “see” next. Of course, serious gardening requires some knowledge, skill and preparation. You’ll need a bit of practice, as I’ve said before, to actually get the desired results. And you’ll need a bit of financial investment too. But even so, survival gardening can still be run on a tight budget, especially in the fertilizer department. The last thing you’ll need to throw your many at is professional fertilizing agents. Don’t get me wrong, these products work, they get the job done, but there are plenty alternatives you’ll find around the house that will work just as well. And most of the stuff you can use as fertilizer would normally be considered waste, and you’d be throwing it away without being aware of its life-sustaining properties.

First and foremost, you need to understand what fertilizer actually is and why it is so important. Plants, in order to grow and develop require certain amounts of nutrients. Sometimes, what the soil provides just isn’t enough. Fertilizer is added to make sure that plants won’t stagnate and that the crops will be plentiful, counteracting a possible depletion of nutrients in the soil. There are 3 major ranks of nutrients that your garden will need:

  • Rank I nutrients (that are needed in large quantities): P (phosphorus), K (potassium) and N (nitrogen)
  • Rank II nutrients (that are needed in moderate quantities): Mg (magnesium), Ca (calcium) and S (sulfur)
  • Rank III nutrients (that are needed in small quantities): Fe (iron), Mn (manganese), Mo (molybdenum), Zn (zinc) and B (Boron)

If you wish to have healthy and nutritious plants, you’ll have to assure that they get most of these beneficial elements during their development. The lack of nutrients won’t allow the plants to develop normally and may even cause their premature death. So fertilizer it’s a must! Let’s have a look at some of the best DIY fertilizers you can find around the house.

Egg shells

As the old saying goes, you can’t make an omelette without breaking a few eggs. But after the omelette is done, don’t throw the egg shells away, they’ll make a great addition to you gardening plan. Egg shells contain a great amount of Ca (calcium), which is extremely important for cellular growth and development. Calcium is one of the elements in the soil that get depleted fastest while plants are growing, so adding some back into the circuit would be extremely beneficial to you garden. Grind the shells into a thin powder and sprinkle them on the ground; that should do it. The shells also contain N and phosphoric acid.

Banana peels

The banana peel is yet another object you’d be tempted to discard right away. But bananas are rich in potassium (K), and so are its peels. Adding banana peels to your garden would ensure rich and well-developed crops, as potassium (K) is a rank I ingredient, which plants can’t get enough of. Not only is it beneficial to all sorts of fruit and veggies, but ornamental plants are loving it also. Don’t throw the peel on the ground directly, rather rip it into shreds and place it in the hole before planting for optimum efficiency.

Coffee grounds

Coffee grounds are an excellent source of magnesium (Mg) potassium (K) and nitrogen (N) and would make great ”food” for the plants. But adding them to the soil will increase the overall pH, so it’s generally recommended to use them more for plants who strive in a more acid environment like tomatoes, avocados, blueberries, azaleas etc. Before scattering them on the ground, it’s best if you let them dry first. You should scatter them lightly, around the plants.

Fire ash

As long as you have ash leftovers from the fireplace or if you’ve been camping all night, you also have a good means of fertilizing your garden. Ash is rich in potassium (K) and calcium carbonate, which will do wonders for growing fruit and vegetables. The ash method works best for plants that love alkaline surroundings; so don’t use the ashes on acid loving plants. And if the ashes are the result of a fire to which charcoal or lighter fluid was added, don’t use them. The residual agents will harm the plants. So use 100% wood ashes only.

Hair

Yes, that’s correct: hair. Any sort of hair will do, be it from people, dogs cats and pretty much any other creature you can think of. Hair is naturally packed with nitrogen, so if you’ll sprinkle it across the garden, you’ll supply the growing plants with a much needed nitrogen (N) boost. Get hair wherever you can find it: scrap it off brushes and save the trimmings from cutting your hair; you can also visit your local barber shop for great amounts of hair that they would otherwise just throw away. Just offer to get it off their hands for free and they’ll most likely let you have it.

And there you have it, some of the easiest and cheapest methods of ensuring the right nutrients for you survival garden. Not only are these methods cheap and convenient, but they’re also very efficient. If it was money that was in your way of getting your hands dirty and your thumbs green, problem solved! You can now have your garden, and on a budget too.

By My Family Survival Plan

Preserving Oral Hygiene In A SHTF Scenario

Preserving Oral Hygiene In A SHTF Scenario

Oral hygiene is of upmost importance, and we’re familiarized with the toothbrush and toothpaste from an early age. Keeping your teeth clean on a daily basis is vital for preserving oral hygiene. But despite the rigors and norms of the modern consumerist society we live in, there are many other ways of keeping your teeth clan and healthy. And they work best in a TEOTWAWKI scenario, when the products we’re used to won’t just be available anymore. You’ll need to improvise, but luckily there are many substitutes for the traditional methods and products. And despite what many people believe, teeth aren’t made of glass. Cleaning them with something else other than toothpaste won’t damage them in any way. There are plenty of raw foods that known to have a cleaning effect on the teeth (apples, pears, carrots); provided they are hard enough (soft and ripe won’t do), they’ll do wonders for your teeth and gums, preventing even gingivitis and canker sores. Here are some of the best replacements for modern teeth cleaning methods.

BAKING SODA

Baking soda is probably the most famous alternative when it comes to cleaning the teeth. The baking soda’s natural properties lets it neutralize acids that are harmful for the enamel, kills off bacteria that is responsible for plaque build-up and as far as aesthetics go, it’s an excellent stain remover. It’s used dates as far back as antiquity, as even Hippocrates himself had a mouthwash recipe based on baking soda, vinegar and alum. Alongside baking soda, there are many oils you can throw into the mix for added beneficial effects: cinnamon oil (has antibacterial and antimicrobial properties), peppermint oil (has antibacterial effect, it freshens the breath and it clears up the sinuses), clove oil (fights off bacteria and has painkilling properties) etc. These oils work in more ways than one. If you have swollen gums, you can dip a piece of clean cloth of gauze in any of these and a place over the affected area; for best results, let the gum-pack sit overnight.

SALT

Salt is the ingredient that no serious prepper should go without. And believe it or not, it even serves a purpose in the field of oral hygiene. Salt brushing can be used even today, in moderation of course; salt can whiten and brighten one’s teeth. It has mild cleaning properties and it can be used daily; you can also make a salt based mouthwash that you can use for disinfection purposes, against bad breath, tartar, plaque and even boost the healing process. Salt can be used raw or mixed with baking soda (30% salt, 70% baking soda); you can even add sage to the mix, if you happen to have some at your disposal. Mouth wash is even easier to make; just add salt to potable water and there you have it.

OXYGENTATED WATER (HYDROGEN PEROXIDE 3%)

The product has been proven to be very effective against gingivitis, canker sores and harmful bacteria. It should be diluted with water before usage, because it’s a bit to abrasive on the teeth. Just mix equal parts of water and hydrogen peroxide 3% and you get a very affective mouth wash. However, you should never swallow the mixture. Before brushing your teeth, swish it around in your mouth and spit it out, but don’t keep it in for longer than 20 seconds. After you’re done, you can wash the toothbrush with the oxygenated water-based concoction, to destroy residual bacteria.

PRIMITIVE TOOTHBRUSHES (aka. CHEW STICKS)

Chewing on sticks and branches is a primitive teeth-cleaning method, that’s still used today among tribal societies. It might seem a bit rough, but it works. The method consists in chewing down on little twigs and branches and splitting them into several small brands. When you’re done chewing and the twig gets spread enough, you can used it to clean your teeth similar to a toothbrush. Some plants are more efficient than others, thanks to their healing properties. Some of the best and most spread DIY toothbrushes can be made out of oak, juniper, eucalyptus and the neem tree. Their rich in tannins that are extremely helpful in cleansing and curing gum-related afflictions and oils that stimulate blood flow.

There you have it, some of the best methods to help you keep your oral hygiene even in the toughest conditions imaginable. When your toothpaste and mouthwash reserves run low, you’ll need to consider replacing them and fast. No matter how bad things get, overlooking oral hygiene is not an option.

The Importance Of A Pocket Chainsaw For Survival

The Importance Of A Pocket Chainsaw For Survival

I am well aware of the fact that most of us that deal with prepping and take surviving in a SHTF situation seriously are familiar with the pocket chainsaw. Many of us have repeatedly used one, no doubt about that. And with good reason too.

The motorized chainsaw is a vital tool to have if you live out in the forest, especially when you are a long way from major roads. It requires very little effort from your part when it comes to cutting down trees or chopping wood (mainly); however you do need to be trained as they can be super dangerous in the wrong hands. Safety clothing such as chainsaw proof pants are a must also. The chainsaw comes in a lot of shapes and sizes and makes the work as easy as possible; all it asks in return is fuel and occasional maintenance.

But no matter how efficient it is in a day-to-day situation, it’s not very reliable when it comes down to a survival scenario. The fuel it requires will stop being a commodity and will become harder and harder to find; same goes for the oil and other parts that are required for maintenance. Plus, you would have to lug it around. If it was a ‘pack what you can carry’ situation, it might get abandoned pretty fast.

Fortunately, there’s an alternative available – and it could be a lifesaver. It’s called the pocket saw, and it’s basically a chain similar to that of a chainsaw, but it has a handle attached at each end of the cutting chain. This gadget will require a lot more effort from your part in cutting wood, as you will need to “become the engine” that drives the chain; but it’s the best option you’ve got. So if some manual labor doesn’t scare you, it will be extremely efficient in a survival scenario, when you’ll need to cut wood for building a shelter, firewood or surpassing and obstacle that might be in your way. The workout will be good for you and keep you warm too!

One of the best things about this particular piece of kit is its portability. A pocket chainsaw takes up a fraction of the space (and weight!) of other types of hand saw.

LIEUTNNT Survival Pocket Hand Chainsaw

This particular pocket chainsaw got tons of 5-star reviews. It has high quality steel teeth and comes in a 36 inch size (21″blade). One feature that really makes the chainsaw stand out are the comfortable plastic handles. This pocket chainsaw should cost around $20 – $25 and as a bonus, you also get a pouch.

The Supreme Products Pocket Chainsaw

The pocket chainsaw put out by Supreme Products also has a bi-directional chain, but what makes it stand out is that the product is modular. The saw can be detached from the handle, and if stored in its box, it weighs only 4 ounces and it can easily be fitted safely inside any pocket. The chain is made of carbon steel that has been coated with an anti-rusting agent. The blade is 28 inches long and the teeth are placed every 1/4 of an inch. At each end of the saw you get a stainless steel hook, to which you can attach the plastic handles, which are more comfortable than the handles made out of fiber, especially when you’ll be using the saw for longer period of time. The purpose of making this chainsaw modular is that you can add extension if you want to rich high limbs; just add as much rope as you like in-between the hooks and the handle. It’s very reliable and sturdy, easy to carry and to assemble and because the blade cuts both ways, you can go through a 3-inch diameter limb in about 10 – 15 seconds. Getting one won’t cost you more than $21.

The SaberCut pocket chainsaw

The SaberCut is released by Ultimate Survival Technologies and it’s a very efficient and qualitative tool. The 24 inch blade is bidirectional, cutting both ways easily because it’s very flexible and durable. The saw weighs in at about 4.5 ounces. It’s one of the easiest-to-maintain pocket chainsaws I ever came across. The teeth are self cleaning and they can easily be sharpened with a standard 1/8 chainsaw sharpener. The handles are made from the same material as the pouch it comes with, which is pretty durable and strong enough. Although this particular saw is not modular, you can always add as much length as you want tying cord to the handles. Not only is the SaberCut efficient and trustworthy, but it’s also one of the cheapest pocket chainsaws you can find, as it costs no more than $11.

The Best Natural Antiseptics You Can Use In A Survival Scenario

The Best Natural Antiseptics You Can Use In A Survival Scenario

When SHTF and the whole world falls apart, surviving each day at a time will be the key issue, as I have stated so many times before. Apart from staying safe and getting the right resources as far and food and water goes, keeping healthy will be just as important. I’ve advised you time and time again on being vigilant and avoid accidents at all costs, as have I advised you on keeping the right supplies in your personal survival medical kit.

But as far as medical supplies go, they’ll run out eventually. And vigilance just won’t be enough to stop accidents from happening entirely. When it comes down to it, you’ll need to improvise, and fast. No matter what type of accidents we’re talking about, be it a minor one (a bruise, a cut, bug bites etc.) or a more serious injury (burns, fractures etc.), a real important part of the treatment is avoiding infection. For such occasions you’ll need to have antiseptics in hand.

They are substances (that come in liquid, powder or ointment form) and get applied locally to help prevent infection, sepsis (harmful bacteria and toxins) and even putrefaction. Medical kits usually have Betadine (aka. Povidone-iodine), which is one of the best medical products when it comes to fighting off infection. But if you don’t happen to have any, there is still plenty of substitutes you can you use. Let’s have a look at what they are.

1. Mouthwash

You might have run out of Betadine, but if you still have some mouthwash lying around, you should be set. If you have a mouthwash that is set on fighting plaque and gingivitis, it should be able to do the same with any sort of pathogens that tend to build up on an open wound. Most of the products in this category have substances like zinc chloride, cetylpyridinium chloride, chlorhexidine (available by prescription) etc., that are nothing else but antiseptic agents. If it’s set to fight off germs in your mouth, it should do the same for cuts, bruises and flesh wounds.

2. Lemon juice

For those of you that have a high tolerance to pain, you can use lemon juice, or even better, lime juice to disinfect and clean open wounds. But be advised that the stinging sensation will be intense. Not only will lemon juice kill off potentially harmful bacterial agents, but it will also stops the bleeding. The juice is effective against pathogens thanks to its acidic properties that act like an alcohol-based disinfectant: it kills of germs, it cleans the wound and it dries up the area all in one swoop. If you can stand the pain, it’ll be worth it. But be advised, excessive use can damage healthy cells as well.

3. Garlic

Garlic is known to be one of the most potent natural antiseptics across many cultures throughout the world. But in order for it to work, the wound needs to have stopped bleeding. Once the bleeding stops, clean the afflicted area with water and gently dry it off with a clean piece of cloth. The garlic can be crushed and applied directly or you can make a concoction by adding red wine. Let it sit for 3 – 4 hours and apply to the wound. However, garlic can be damaging to the skin, so don’t leave it more than 25 minutes at a time.

4. Potatoes

I bet not many of you knew that potatoes have a natural ability of healing open wounds. Well, they do. And it’s all based on their ability to attract and draw out all sorts of infections. The first thing you’ll need to do is to shred a potato or two and spread them over a thin, clean cloth. Add this to the wound and let it sit for 5 hours at a time. When changing your potato bandage with a fresh one, you’ll need to clean the wound with some salt-water. Potatoes will keep the inflammation to a minimum and will keep pathogens at bay.

5. Chamomile

Chamomile is an ancient cure for so many ailments, that its notoriety has lasted through the ages. The plant’s dried flowers contain high levels of flavonoids and terpenoids that make it one of the most curative plants to have been discovered. If chamomile-based ointments or medicine isn’t available, you can easy get some tea bags or simply find fresh flowers, dry them and make them into tea. Once the tea is done, get a clean cloth and soak it in. Drain the excess liquid and apply directly on the wound; if you have chamomile tea bags, even better, as they’ll contain plant parts which will speed up the healing process even more.

6. Cayenne pepper

The Cayenne pepper works amazingly as open-wound treatment. Not only does it have anti-bacterial and anti-fungal properties, but it also stops the bleeding in a heartbeat, as it makes the blood clot way fast than normal. The bleeding of a superficial wound should cease in about 15 seconds after the pepper was added; if the wound is more severe, drink the concoction made up of 8oz water + 1oz cayenne pepper daily. This will help you cause.

7. Pine sap + needles

The pine sap is considered as one of the most easily procured natural antiseptics there are. If you happen to have some pinesin you vicinity, getting some sap will be child’s play. Look on the body of the tree for lumpy formations. They or sap pockets witch you can easily pop or stick with your knife. Once the sap is out, simply take it and spread it over the wound. If you wish to strengthen the effect of the sap, you can grab some pine needles to snack on. They are edible and also have mild antiseptic properties.

8. Cactus bandages

This is the best option for all you desert-dwellers out there. The prickly pear cactus (Oputia sp.) has flat round pads, which have excellent antiseptic and astringent properties. Grab a pad and either split it in half or peel it. Place it directly over the wound, but assure yourself you have removed those pesky needles first. You can let it sit, even secure it with a gauze. The cactus will speed up the healing process.

Whether you’ll need to resort to such improvisations or not, is hard to tell. But if it ever comes down to it, at least you won’t have to endure a slow and painful death caused by infection. Nature is lending us a hand every here and there, just keep your eyes open.

By My Family Survival Plan

How To Treat A Burn Victim In A Survival Scenario

How To Treat A Burn Victim In A Survival Scenario

The danger of getting burned is ever-present in our day to day lives. Whether we’re talking about a minor burn caused by carelessness or a severe degree burn caused by an unfortunate event, it’s important to know how to react in such a situation. Most of us have already dealt with burning injuries at least once in their lifetime, so the sensation and the gravity of the matter is known to most people. We’re not lacking in the health department in this day and age; there’s plenty of doctors and clinics out there that are able and equipped to deal with burn victims. Even if they’re not immediately available, medicine is widely available and many people already have their stock set aside for darker days. But what happens in TEOTWAWKI situation, when medical care and supplies won’t simply be available anymore? In this case, it’s important to know how to treat a burn victim and to improvise as best as we can in order to save one’s life.

The first thing we’ll need to asses in a burning accident is how much of the overall body surface has been affected by the burn. People that have less than 20% of their body’s surface affected by 2nd and 3rd  burns are not facing direct life threats (although the danger of infection and complications is still present); 1st degree burns do not pose a life threat, as the skin is not significantly affected. But those who have suffered. This is easily calculated by using the rule of nines, according to whom the surfaces on the human adult body are as follows: head = 9%, chest (front) = 9%, abdomen (front) = 9%, upper/mid/lower back & buttocks = 18%, arms (each) = 9%, palm (each) = 1%, groin = 1%, legs (each) = 18% (front = 9% + back = 9%).  For children, the numbers are as follows: head = 18%, chest (front) = 9%, abdomen (front and back) = 9%, upper/mid/lower back & buttocks = 18%, arms (each) = 9%, palm (each) = 1%, groin = 1%, legs (each) = 14% (front = 7% + back = 7%).

After the affected surface area has been determined, it’s imperative to understand what degree of burn you’re dealing with. As an international convention, burns are split into three distinctive categories:

1st degree burns or mild burns are what happens in the best case scenario. The injury is superficial and the skin is not completely affected. A good example of a 1st degree burn is a nasty case of sunburn. It requires a lesser form of treatment and it’s not life-threatening

2nd degree burns are much more serious and pose a greater threat to general health. They are far more painful as the affliction penetrates far deeper into the skin. If this is the case, it’s recommended you seek medical help, if available.

3rd degree burns are the most severe types imaginable. Because the injury goes so deep into the skin, the pain receptors can be completely destroyed, so they victim might not feel pain at all. If the affected area gets swollen, turns leathery or black, you’re dealing with a 3rd degree burn; as a mentioned before, pain is no longer an indicator. This is an emergency, and you should seek professional help if it’s available, if not, turn to your medical kit.

Before you start applying a treatment, you’ll need to determine the nature of the burn. Various types of burns require different treatments. These are some of the most common causes when it comes to burn injuries and how you should deal with them:

If the victim has been subjected to a flame source, the first step is to take the person away from the fire source and to extinguish his clothes if they’re on fire. Water is the best choice, as this will not only put out the fire, but it will also wash away any remaining pieces of charred clothing. Cold water will cool the burned areas and sooth the pain. Next, remove the clothes, gently tap with a dry and clean piece of cloth and apply any treatment available.

Treating electrical burn victims requires a different approach. In this case, the insides are just as damaged (if not more) than the outside. Electrical current takes a toll mostly on the heart, so before treating burns, check the patient’s vital signs first. You might need to perform CPR before anything else. Once the victim is stabilized, you can proceed to treating the burns.

Chemical burns are also a hazard to take into consideration. Treating skin that’s been exposed to corrosive substances requires a lot of patience. The burned area should be washed with water for about 30 minutes before proceeding to apply any type of ointment. If the area is not cleaned perfectly, the remaining substances will continue to destroy skin cells. After the area has been cleaned, you should double check that the ointment you’re about to apply won’t react with the chemical residue found in the burn.

If medical help is not available and if your personal survival medical kit is depleted, worry not. Luckily you can still improvise burn treatments out of everyday household items. Here are some of the things found around the house that can do wonders in case you’re dealing with burns:

  1. Honey is a fantastic first aid solution when it comes to treating burns. It can also work as a permanent solution, provided you’re in a survival scenario and you happen to have some honey lying around. You should cover the affected surface in honey completely. Next cover the area in a plastic warp. Honey will prevent bacteria from reaching the wound and keep the risk of infection to a minimum. Check the wound daily and apply as much honey as you can spare.
  2. Vinegar can also be used for cleaning the burned area, as it can be used as an antiseptic. Because it’s an acid, the vinegar will sting and add to the burning sensation, but in the process it will clean and sanitize the burned area, killing of any unwanted pathogens that might lead to severe infection. Diluted vinegar is the way to go.
  3. Baking soda works perfectly for treating a burned area. Just add water, turn it into a paste and apply it gently over the burned area. The baking soda will help reduce the swelling and the pain sensation. You can add it to any type of burns EXCEPT chemical burns. It may give an unwanted reaction with the chemical that caused the burn, so avoid using it in this case.

Aiding a burn victim in no easy task, and you should take it seriously. Educate yourself in the field before taking on such a task, as the wrong move might have unwanted consequences. There are many popular treatments that do not give great result, quite the opposite. Burns should be cleaned with cold water, but never ice water. You might have been told at some point to press something cold next to a burn, but you strongly advise you not to. The surface you might be pressing into the burned area might be carrying pathogens that will cause infection. Also egg whites and oil do not work either, so don’t bother. If your hands and fingers have been burned, remove rings and jewelry asap, because burned areas tend to get swollen. Nasty burns will most likely result in enormous blisters; do not pop them! They’re helping the healing process. Popping them may result in infection, pain and permanent trauma.

NOte – this is an informational article and not to be seen as medical advice nor substitute for consultation with a medical professional, nor a recommendation to self-diagnose or self-treat.

Survival First Aid: Treating Bone Fractures

Survival First Aid: Treating Bone Fractures

Broken bones, fractures and joint injuries are a common thing that happen on a daily basis. We’re only one phone call away from receiving immediate medical assistance if in need. It’s not a life threatening situation in the 21st century, unless there are immediate complications. But what if we happen to brake a hand or a leg in a TEOTWAWKI scenario, where medical assistance will cease to be a commodity and when our very survival will depend on our mobility and full functionality? In case this happens, all is not lost, there are procedures to follow that will get as out of harm’s way. But if the treatment is to be successful, you’ll need to do everything by the book. The first thing to do is to make sure that the injured person’s life is not threatened in any way; once he’s out of harm’s way you can start treating the injury. Once his vital signs have been checked and you’ve concluded that he has been completely stabilized, you can start treating the fracture.

First and foremost, you’ll need to make sure that what you’re dealing with is a fracture and not something else. Most commonly fractures bear the following signs and symptoms: the inability to use or bear weight on the affected body part, severe pain, swelling, deformity, discoloration etc. In some cases, the ones that suffer the injury might even hear a loud cracking noise. In extreme cases, the fracture is so bad that the bone will pierce the flesh. Apart from bone fractures there are other injuries that are easier to treat and not as severe, but can be just as debilitating if left untreated, like muscle strained ligaments and joint dislocations. Fractures can be very tricky and should be approached with care. Many complications can arise (damaged blood vessels, torn muscles, damaged nerves), so minimal and gentle manipulation is imperative. If the affected area becomes swollen, pale, numb and the patient succumbs to shock, it’s probably that an important blood vessel has been damaged, causing internal bleeding. In this case, you should put on hold the fracture treatment and stop the hemorrhaging instead.  The best method of dealing with broken bones is splinting. Many people would advise that the splint should be applied without traction, in the position found, but this would be completely impractical, as the bone should be placed in an anatomically correct position in order to prevent severe pain and loss of function (partial or even complete). So it’s ok to manipulate the fracture gently.

Broken legs

You’ll need two forked branches that are strong enough, so you’ll need them to be at least 2 inches in diameter. One should measure the exact distance from the armpit to 12 inches past his broken leg, while the other should measure the distance from the groin to 12 inches past the broken leg. Next you’ll need to pad the splints. The ends that go past the leg (that measure 12 inches past the leg) will get a 2 inch in diameter branch placed in between them. Now the two splints should be tied together accordingly with the splinting guidelines with anything you can get your hands on: cloth, vines, rope etc. With the same material (provided it’s strong enough), tie a wrap around the ankle; the free ends will get tied to the cross member. Finally, add a twisting stick at the free end of the ankle wrap; twisting the wrap will provide traction. Continue twisting until the broken leg is in line with the healthy leg.

Broken feet

Splinting a foot will require a piece of long and tough cardboard or plastic. This piece of material should be bent lengthwise so that you get three identical (more or less) segments. You can add cloth or padding on the inner side to add comfort. Place the splint under the foot and the leg, so that it reaches halfway to the knee, yet it goes enough under the foot to immobilize the ankle; once this is done, add some cloth between the ankle and splint. Fold the cardboard around the leg and secure it with some tape.  Now do the same as you did with the ankle for all the empty spaces between the leg and the splint: add cloth. You can reduce swelling and discomfort with ice, but don’t keep it on for longer than 20 minutes.

Broken arms

Once the arm is adjusted in its natural position, you should apply the splints. You can use any material as long as it’s hard enough (strong cardboard, sticks, wood etc.) and long enough, so they extend passed the wrist and the elbow. Before the splints go on, wrap the arm in a clean and soft cloth, for comfort more than anything. Once the arm is wrapped, you can wrap the splints as well. The splints should be applied equally when it comes to length; for forearm fractures the splints should go beyond the wrist, while in the case of upper arm fractures, they should extend beyond the elbow. The cloth that holds the splints together should be at least 5 inches before and after the fracture. Don’t tie the bonds too firmly; if you can slip two fingers in, it’s perfect. In order to keep the arm secure and in place, tie a piece of cloth around the neck of the patient and slip the fractured hand in it. The hand should be centered on the sling and it should be at a flat and horizontal position. If the elbow is at a 90 degree angle, you’ve done an excellent job.

Broken hands

Securing a broken hand in place will be a bit trickier, as you’ll need a material that is strong and rigid enough to hold the hand in place, yet flexible enough to fold. It should extend from the wrist to the end of the fingers. The hand should be straight and relaxed, with its fingers slightly opened. Place some cloth in the palm of the hand and place the first splint under the wrist, so it extends to the end of the fingers. The splint should be folded up and around the wrist. Tie it together and add tape for extra security. Once you’re done, stuff the open spaces with cloth to increase comfort and firmness.

If you ever find yourself in the posture of treating broken bones or fractures, remember the first thing to do is to keep calm and act with caution. You’ll need to be very aware and have enough knowledge in the matter. You can educate yourself further in anatomy of the limbs and learn a few knots that will secure your splints in place. You can practice these techniques and even take up courses for first aid, so you won’t have to do it for the first time in a SHTF situation.

By My Family Survival Plan

How To Improvise A Fishing Rod

How To Improvise A Fishing Rod

Every serious fisherman knows the importance of owning the right fishing rod. Whether you’re fishing for sport or you’re simply trying to feed yourself, there’s no better way than doing it the old fashioned way. But in a SHTF situation (whether you’re lost in the wilderness or you’ve found yourself trapped in an end-of-days scenario) you might not have you trusted fishing rod on you. But you won’t necessarily need to. You’ll need nothing more than a knife; having a small tackle box with the right assortment of hooks and some spool of monofilament will make things easier. If you’re lucky enough to have these items on you, you’ll need to improvise the fishing pole only, which it’ll be more than enough to feed yourself in desperate times. If not, well, you’ll need to improvise the whole thing. The rest of the materials you can easily find in your surroundings. And here’s how to do it.

The pole

The first thing you’ll need to find is the pole; any 6 – 7 foot-long branch will do, as long as it’s no thicker than a human thumb. Once you’ve found the right one, you’ll have to break it off from the tree. Once this is achieved, you’ll need to break it again to the desired length. If it’s dry enough, you can snap it in half against your knee or against any hard surface; but if it’s not dry and it’s still rather flexible, you can try cutting it with the knife. Using dead branches is a bad idea because their durability is very low and break easily. You can test the tip by banding it to the point of snapping. If it snaps, fine; the more it does snap, the stronger the remaining pole gets. As soon as you got the pole to the desired length, use the knife to remove any remaining branches, leaves or shoots. Make it as smooth as possible in order to improve weight and handling.

The fishing line

If you happen to have some monofilament fishing like on you, your job gets much easier. If you don’t, sewing thread could get the job done as well. But in sewing thread isn’t an option either, you’ll need to get your hands dirty and look for thin green vines in ground cover or in the undergrowth found around various bushes. The greener the vine, the stronger it will be. If you find a vine that’s about 10 feet, look no further. Remove any tendrils by pulling carefully so you don’t damage the line. For safety, the line should be tied midway down the pole and wrapped as many times as possible towards the tip, where a simple overhand knot will suffice for holding it in place. This way, if the pole breaks, you can immediately catch the line with your hands.

The hooks and the bait

Some professional hooks will work extremely well, provided of course you brought some along. If not, you can always use paper clips, safety pins or soda can tabs. Another viable option is to carve your very own V-shaped hooks out of wood (green wood preferably). A one end you’ll need to carve a groove, in the hook-eye area. This will allow you to tie fishing line onto. As bait you can use pretty much any insect you can get your hands on. The easiest things to get are the earthworms, which can be found underground, under rocks, around moss and in other moist areas. Once you’ve baited the hook, you’re pretty much ready to go. From here on in it’s all about patience and skill.

When it comes to fishing is a SHTF / TEOTWAWKI situation, fishing areas are very important. It’s absolutely necessary to procure the maximum amount of fish with as little resources as possible. So it’s not all about the gear that you have or that you’ve crafted. It’s just as important to know where, when and how to fish. If you’re fishing in stagnant waters, you’ll need to go after still pools. The stillness of the water will make the bait as visible as possible, thus increasing your chances of catching something fast. When it comes to running waters, the area behind exposed boulders would be the best location to catch anything, as fish have a tendency of gathering in such places. You might also want to consider bank fishing, as standing on the water’s edge can also be a very productive fishing method.

As you can see, improvising and entire fishing pole is a rather difficult task, but not impossible to achieve. As previously stated, having line and hooks on you will spare you a lot of trouble. But if not, you’ll just need to put some extra effort into it. Just follow all the steps and you’ll have your DIY fishing rod in no time.

By My Family Survival Plan

7 Unusual Uses For The Usual Egg

7 Unusual Uses For The Usual Egg

Chicken eggs are a part of everybody’s diet; well, everybody who understands the importance of a balanced diet that is. Not only are they tasty, easy to handle and prepare, but they’re also extremely versatile in the kitchen: you can eat them raw, boiled, fried and in billions of combinations for billions of recipes. Yes, eggs area edible, we’ve figured that part out already. But just because they’re good for eating, doesn’t mean that they’re not good for anything else. You’d be surprised to discover that the good ol’ egg is not the boring item you’ve known all your life. There are plenty of other good uses for the egg and they have nothing to do with appeasing your hunger. Because of its wonderful properties, the egg (egg white, egg yolk and eggshell) can be used for the following purposes:

1. Make candles out of eggshells

An emptied eggshell will make an excellent support for a candle. Just drill a hole in the upper side of the egg and once this is done, simply start peeling the eggshell little. Pour out the content (the white and the yolk) and stop peeling when you’re left with 2 / 3 of the eggshell. You can pour melted wax gently and start a candle from scratch in the eggshell or you can improvise one. Just add a candle inside and, preferably, surround with melted wax.

2. Temporarily plant seeds in eggshells and egg cartons

Get an egg carton and have it filed with half eggshells. Next, fill up each and every single half shell (or as many as you need) with soil and press the sides inside it. Because the eggshell contains many nutrients, the plants with develop better this way, especially in the incipient phases. Once the seedlings reach 3 – 4 inches, you can take them out of the eggshells and transplant in normal gardening conditions and settings. The remaining eggshells should not go to waste; you should crush them and add them to the compost. Not only will they give a boost of calcium to the soil, but they will also deter slugs and other pests.

3. Increase your calcium intake

The calcium found in the eggshells can also be beneficial to human beings, especially to those who have deficiencies in the matter. You have to get some empty eggshells and bake them at 250° for about 25 minutes. Once the baking is done, take them out and let them cool. Once they’ve cooled, you’ll have to grind them shells into the finest powder you can. This is in fact a DIY food supplement that you can add to your juice or smoothie; if your pet has calcium deficiencies, you can add it to the dog / cat food as well.

4. Make better coffee

Get your hands on some dry eggshells and crush them. You don’t have to crush them into the thinnest powder, so don’t waste time on doing it. Now take the crushed shells and add them to your coffee just before brewing. The calcium-rich shells will greatly improve the overall taste of the coffee, as it will absorb a great deal of its natural bitterness. After you’re done with the coffee, don’t throw the leftovers away. The grounds and the shells can be added to your compost heap and re-used for gardening purposes.

5. Cleanse your skin

Science has proven that egg whites have an amazing effect when it comes to clearing up complexions, tightening skin and destroying acne. If you need some skincare and you don’t have any professional skin products in reach, you can make your very own remedy by combining an egg white with half a tea spoon of lemon juice. Beat the concoction gently, place it on the area you wish to treat and let it sit until it dries. Once is dry, apply a second layer for maximum effect. After the second layer is applied, let it sit for 10 – 15 minutes; once the time is up, wash your face with warm water.

6. Moisturize you skin

If egg whites are great for skin afflictions, egg yolks do wonders for dry skin. They are rich in lecithin, which is very effective against dry skin. You’ll have to make a face mask following this recipe: mix an egg yolk, ad 3 teaspoons of honey; stir gently until you’ve obtained an homogenous paste. Apply the paste on the face, in a thick layer. You have to let it dry and sit for about 20 minutes. Once the 20 minutes are up, remove the mask by washing it with warm water.

7. Glue for paper and light cardboard

If you need to glue some paper, cardboard or some other light materials and you don’t happen to have any glue around, a simple egg white will suffice. Just break an egg, separate the egg white from the egg yolk, dip a brush in the egg white andspread it gently on the surfaces you want to glue together. The egg white contains proteins that tend to get very sticky when they dry up. It works excellent for paper or light cardboard at least; not recommended for heavier materials.

Believe it or not, the many uses of eggs do not even stop here, I’m sure there are plenty more tasks that the apparently-average egg can fulfill. Maybe many haven’t even been discovered yet. All in all, it really pays having some eggs around the house. Whether you’re looking to achieve some wacky goal or you’re simply trying to grab a bite to eat, a couple of eggs could be just the thing you need; especially if there’s some bacon involved.

By My Family Survival Plan

WordPress Themes